shell holder question 7.62 Luger

DAVID · 03-31-2001, 09:12 PM

Just got a set of CH dies for the .30 luger and my Lyman 9mm shell hold will not accept the rim on the Winchester Western cases. Any ideas. TIA David.

Frank · 03-31-2001, 09:45 PM

David, RCBS shows the same shell holder for the 9mm and 7.65mm (.30 Cal) Lugers. Also, the 9mm front end is just a blown out 7.65 to get rid of the bottle neck, the rear end didn't change. You might try an RCBS, if it fits your press. I can't imagine the WW cases are that much different. Good Luck.

Hugh · 03-31-2001, 10:36 PM

David, check the cases to see if the hang up is because the extractor groove is not deep enough, or if the rim is to thick. Then you will know where to apply your small file to the shellholder so that it will accept the cases.

BILL · 04-01-2001, 05:10 PM

RCBS should use the same shellholder for 9mm and 7.65mm. I have loaded many over the years and used RCBS equipment.

BILL · 04-01-2001, 05:11 PM

DAVID · 04-01-2001, 10:57 PM

04-02-2001, 05:06 PM

The RCBS shell holder is #16 for both cals.

Regards

03-31-2001, 09:45 PM	#2
Frank RIP Patron LugerForum Patron Join Date: Jun 2002 Location: Hot & Dry PHX, AZ Posts: 2,078 Thanks: 24 Thanked 163 Times in 87 Posts	Re: shell holder question 7.62 Luger David, RCBS shows the same shell holder for the 9mm and 7.65mm (.30 Cal) Lugers. Also, the 9mm front end is just a blown out 7.65 to get rid of the bottle neck, the rear end didn't change. You might try an RCBS, if it fits your press. I can't imagine the WW cases are that much different. Good Luck.

03-31-2001, 10:36 PM	#3
Hugh RIP Join Date: Jun 2002 Location: Southeast Texas Swamp Posts: 2,460 Thanks: 2 Thanked 165 Times in 64 Posts	Re: shell holder question 7.62 Luger David, check the cases to see if the hang up is because the extractor groove is not deep enough, or if the rim is to thick. Then you will know where to apply your small file to the shellholder so that it will accept the cases.

04-01-2001, 05:10 PM	#4
BILL User Join Date: Jun 2002 Location: Western Washington Posts: 826 Thanks: 0 Thanked 0 Times in 0 Posts	Re: shell holder question 7.62 Luger RCBS should use the same shellholder for 9mm and 7.65mm. I have loaded many over the years and used RCBS equipment.

04-01-2001, 05:11 PM	#5
BILL User Join Date: Jun 2002 Location: Western Washington Posts: 826 Thanks: 0 Thanked 0 Times in 0 Posts	7.62 or 7.65?? (EOM)

04-01-2001, 10:57 PM	#6
DAVID User Join Date: Jun 2003 Location: Debary, FL. Posts: 129 Thanks: 0 Thanked 0 Times in 0 Posts	Re: sorry mind was out of gear. (EOM)

03-31-2001, 09:12 PM	#1
DAVID User Join Date: Jun 2003 Location: Debary, FL. Posts: 129 Thanks: 0 Thanked 0 Times in 0 Posts	shell holder question 7.62 Luger Just got a set of CH dies for the .30 luger and my Lyman 9mm shell hold will not accept the rim on the Winchester Western cases. Any ideas. TIA David.

04-02-2001, 05:06 PM	#7
REB Guest Posts: n/a	Re: sorry mind was out of gear. The RCBS shell holder is #16 for both cals. Regards

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode