Krieghoff Tool marked /40

dz · 01-10-2007, 09:27 PM

With a 1940 Krieghoff Luger came a tool that I was told was Krieghoff. The only marks were /40 Has anyone ever seen this? Thanks David

Navy · 01-10-2007, 09:34 PM

David,

I sincerely doubt it is a Khoff tool. In fact, it doesn't have the shank length that all tools I have seen display. Maybe a Krieghoff Kurtz?

Tom A

George Anderson · 01-11-2007, 08:41 AM

Like Tom noted, the dimensions are wrong. Also the is no lip in the left third of the hole.

dz · 01-11-2007, 10:54 AM

Thanks for responding, there is a lip on the bottom of the hole which the photo does not show. David

Pete Ebbink · 01-11-2007, 01:43 PM

Not to say the tool shown is legit...

But there are some dimensional differences amongst TD toolks shown in E. Bender's large book...amongst police tools. Probably the same with the other Issues, as well.

Pete Ebbink · 01-14-2007, 05:43 PM

David,

Here's an HK tool I picked up for my S-Code rig...

lugerholsterrepair · 01-14-2007, 05:58 PM

David, The wings are very sharp cornered as well as the other criticizms made before me by my learned colleques. I would say it is a repro that was marked in order to inhance it's value. Maybe the runt of the litter? If I were to see it on a gun show table for ten bucks it would still be there when I left.

Pete, A real beauty!

Jerry Burney

dz · 01-15-2007, 12:22 PM

Thanks you all for your comments. DAvid

lugerholsterrepair · 01-15-2007, 12:43 PM

David, It's still a usefull tool..I keep a repro in my shooting box to do as it was designed to do, load magazines and act as a screwdriver. This is just not what a collector is looking for. Jerry Burney

01-10-2007, 09:27 PM	#1
dz Patron LugerForum Patron Join Date: May 2004 Posts: 259 Thanks: 1 Thanked 55 Times in 39 Posts	Krieghoff Tool marked /40 With a 1940 Krieghoff Luger came a tool that I was told was Krieghoff. The only marks were /40 Has anyone ever seen this? Thanks David Attached Thumbnails

01-14-2007, 05:58 PM	#7
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	David, The wings are very sharp cornered as well as the other criticizms made before me by my learned colleques. I would say it is a repro that was marked in order to inhance it's value. Maybe the runt of the litter? If I were to see it on a gun show table for ten bucks it would still be there when I left. Pete, A real beauty! Jerry Burney __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

01-15-2007, 12:43 PM	#9
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	David, It's still a usefull tool..I keep a repro in my shooting box to do as it was designed to do, load magazines and act as a screwdriver. This is just not what a collector is looking for. Jerry Burney __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-10-2007, 09:34 PM	#2
Navy RIP Join Date: Jun 2002 Location: Dc 'burbs in Virginia Posts: 2,482 Thanks: 0 Thanked 16 Times in 10 Posts	David, I sincerely doubt it is a Khoff tool. In fact, it doesn't have the shank length that all tools I have seen display. Maybe a Krieghoff Kurtz? Tom A

01-11-2007, 08:41 AM	#3
George Anderson Lifer Lifetime Forum Patron Join Date: Jul 2002 Location: VA Posts: 3,592 Thanks: 1,773 Thanked 2,529 Times in 787 Posts	Like Tom noted, the dimensions are wrong. Also the is no lip in the left third of the hole.

01-11-2007, 10:54 AM	#4
dz Patron LugerForum Patron Join Date: May 2004 Posts: 259 Thanks: 1 Thanked 55 Times in 39 Posts	Thanks for responding, there is a lip on the bottom of the hole which the photo does not show. David

01-11-2007, 01:43 PM	#5
Pete Ebbink User Join Date: Jun 2002 Location: The USA Posts: 5,919 Thanks: 0 Thanked 6 Times in 4 Posts	Not to say the tool shown is legit... But there are some dimensional differences amongst TD toolks shown in E. Bender's large book...amongst police tools. Probably the same with the other Issues, as well.

01-14-2007, 05:43 PM	#6
Pete Ebbink User Join Date: Jun 2002 Location: The USA Posts: 5,919 Thanks: 0 Thanked 6 Times in 4 Posts	David, Here's an HK tool I picked up for my S-Code rig...

01-15-2007, 12:22 PM	#8
dz Patron LugerForum Patron Join Date: May 2004 Posts: 259 Thanks: 1 Thanked 55 Times in 39 Posts	Thanks you all for your comments. DAvid