Hugh's 30 Luger Long Barrel

Thor · 03-31-2002, 11:17 PM

This dude is sporting an 8" barrel and a big amount of UNIQUE powder will boost that 60 grain HP to light speed. The bullet was designed to operate at 700-800 fps in a 32 Auto I think so at 1400 fps it should come unglued with explosive force. I will have to test it out for accuracy next week. I have the Luger blued and will be finishing it up tomorrow or Tuesday. Hugh has sized these bullets to .3095". Full report in a view days. I will be shooting the Winchester 30 Luger cases I bought from OWS (Old Western Scrounger) ~Thor~

Kyrie · 04-01-2002, 09:17 PM

Hi Ted,

I once used 95 grain JHP bullets designed for use in .38 Special ammunition, and to open up at 800 fps, to load some .357 Magnum cartridges. At 1600 fps the angular momentum would cause these bullets to literally come apart in mid air. At ten yards, each shot would leave a nice bullet hole in a paper target - and each bullet hole would be surrounded by a circle of tiny fragment holes. At twenty-five yards there wouldn't be a mark on the target anywhere. Sometimes too much velocity is not a good thing!

Best regards,

Kyrie

Moderator - Cruffler_Forum on Yahoo Groups

"The flame free C&R Forum."

Thor · 04-01-2002, 10:49 PM

Kyrie, I dont doubt it one bit! I once had some SX Hornaday bullets do the same thing in mid air, they left little gray tracer trails as they came apart. Hugh has fired these 30 Luger bullets at these speeds so I think they will work well. I will report any keyholing or fragmenting as evident by the paper targets. ~thor~

03-31-2002, 11:17 PM	#1
Thor User Join Date: Jun 2002 Location: Rio Rancho, New Mexico Posts: 4,583 Thanks: 958 Thanked 970 Times in 276 Posts	Hugh's 30 Luger Long Barrel This dude is sporting an 8" barrel and a big amount of UNIQUE powder will boost that 60 grain HP to light speed. The bullet was designed to operate at 700-800 fps in a 32 Auto I think so at 1400 fps it should come unglued with explosive force. I will have to test it out for accuracy next week. I have the Luger blued and will be finishing it up tomorrow or Tuesday. Hugh has sized these bullets to .3095". Full report in a view days. I will be shooting the Winchester 30 Luger cases I bought from OWS (Old Western Scrounger) ~Thor~

04-01-2002, 09:17 PM	#2
Kyrie User Join Date: Jun 2002 Posts: 757 Thanks: 0 Thanked 212 Times in 101 Posts	Re: Hugh's 30 Luger Long Barrel Hi Ted, I once used 95 grain JHP bullets designed for use in .38 Special ammunition, and to open up at 800 fps, to load some .357 Magnum cartridges. At 1600 fps the angular momentum would cause these bullets to literally come apart in mid air. At ten yards, each shot would leave a nice bullet hole in a paper target - and each bullet hole would be surrounded by a circle of tiny fragment holes. At twenty-five yards there wouldn't be a mark on the target anywhere. Sometimes too much velocity is not a good thing! Best regards, Kyrie Moderator - Cruffler_Forum on Yahoo Groups "The flame free C&R Forum."

04-01-2002, 10:49 PM	#3
Thor User Join Date: Jun 2002 Location: Rio Rancho, New Mexico Posts: 4,583 Thanks: 958 Thanked 970 Times in 276 Posts	Re: Hugh's 30 Luger Long Barrel Kyrie, I dont doubt it one bit! I once had some SX Hornaday bullets do the same thing in mid air, they left little gray tracer trails as they came apart. Hugh has fired these 30 Luger bullets at these speeds so I think they will work well. I will report any keyholing or fragmenting as evident by the paper targets. ~thor~

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode