New to Lugers and the Forum

normrp · 12-05-2005, 08:50 PM

Hello All,

I recently got my first Luger and am pretty jazzed about it. It is a shooter and a little rough around the edges but I think it is in decent enough shape. The barrel and receiver are #3563, sideplate #63, toggle #33, frame #2787, sideplate latch #99.

It is dirty and I need to completely disassemble and clean it before I fire it. The mag is made by Erma.

I need to replace the trigger because some goofball took a dremel to it and ground the right side of the trigger face. It has some gouges in it from from this. Why it was done I have no idea.

I paid $385 for it and thought that was ok for a shooter.

Here are some pics.

normrp · 12-05-2005, 08:54 PM

another pic

normrp · 12-05-2005, 08:59 PM

the other side

normrp · 12-05-2005, 09:02 PM

another pic

normrp · 12-05-2005, 09:04 PM

last one for now

pipeman45 · 12-05-2005, 09:43 PM

Not bad.A mis match can make a fine shooter. Be sure to have it checked out and let us know how it shoots.

Edward Tinker · 12-05-2005, 11:02 PM

Well worth the money, hard to find a shooter for $500, let alone under $400!

Welcome to the forum!

Ed

normrp · 12-06-2005, 09:58 PM

Thanks.

From the treading I have done lurking out here there is a ton of info available from all of you.

I figure it will be after the first of the year before I can get to the range with it. I have been studying the take down instructions and think I am ready to tackle it!

Norm

12-05-2005, 08:50 PM	#1
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	New to Lugers and the Forum Hello All, I recently got my first Luger and am pretty jazzed about it. It is a shooter and a little rough around the edges but I think it is in decent enough shape. The barrel and receiver are #3563, sideplate #63, toggle #33, frame #2787, sideplate latch #99. It is dirty and I need to completely disassemble and clean it before I fire it. The mag is made by Erma. I need to replace the trigger because some goofball took a dremel to it and ground the right side of the trigger face. It has some gouges in it from from this. Why it was done I have no idea. I paid $385 for it and thought that was ok for a shooter. Here are some pics. Attached Thumbnails

12-05-2005, 09:02 PM	#4
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	another pic Attached Thumbnails

12-05-2005, 09:04 PM	#5
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	last one for now Attached Thumbnails

12-05-2005, 11:02 PM	#7
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,935 Thanks: 2,034 Thanked 4,533 Times in 2,093 Posts	Well worth the money, hard to find a shooter for $500, let alone under $400! Welcome to the forum! Ed __________________ Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-05-2005, 08:54 PM	#2
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	another pic Attached Thumbnails

12-05-2005, 08:59 PM	#3
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	the other side Attached Thumbnails

12-05-2005, 09:43 PM	#6
pipeman45 User Join Date: May 2004 Location: Kentucky Posts: 539 Thanks: 0 Thanked 1 Time in 1 Post	Not bad.A mis match can make a fine shooter. Be sure to have it checked out and let us know how it shoots. __________________ Dave

12-06-2005, 09:58 PM	#8
normrp User Join Date: Jun 2005 Location: Salem Orygun Posts: 6 Thanks: 0 Thanked 0 Times in 0 Posts	Thanks. From the treading I have done lurking out here there is a ton of info available from all of you. I figure it will be after the first of the year before I can get to the range with it. I have been studying the take down instructions and think I am ready to tackle it! Norm