Luger Blank Adapting

Feldkanone · 10-25-2018, 01:22 PM

Hello,

Does anyone offer any guidance on adapting a luger for blank adapting? I know it has been done and I have a beater I would like to convert. I know I will need to restrict the barrel and and I believe modify the toggle area to cycle.

Thank you!

Vlim · 10-25-2018, 01:25 PM

Normally speaking, threading the inside of the barrel from the muzzle end, and installing a suitable plug with a small vent hole will do the trick. Working out the diameter of the vent hole is the hard part.

That is how they murder P08 pistols over here for re-enactors, at least.

Feldkanone · 10-25-2018, 01:39 PM

Yes, but doesn't the action need to be modified so that it will cycle just from the pressure created by the barrel plug? Won't it stay locked without the normal recoil from a live round?

Vlim · 10-25-2018, 02:41 PM

The pressure needed to cycle the gun should be generated by the plug with vent hole itself.

Similar systems have been used for years as gov't training adaptors. I have shot a 9mm uzi with blanks and a barrel adaptor, these were fitted over the muzzle. AR15's had similar adaptors fitted. All with the same basic principle: reduce muzzle size to increase gas pressure to facilitate cycling on a blank.

Diver6106 · 10-25-2018, 04:05 PM

If the blanks have a very reduced load of powder, such as not cycling with a fully blocked barrel, you might need to get a weaker main spring for the toggle. Or you could shorten the existing spring to weaken it, by clipping loops off. Or even better - just get a cap pistol.

sheepherder · 10-25-2018, 04:40 PM

Quote:

Originally Posted by Vlim

AR15's had similar adaptors fitted.

When I went through ITR, an instructor showed us a 'field expedient blank adapter'. He stuck the first section of the M16 cleaning rod (the part with the handle) into the muzzle and pressed the rod/rifle against a tree. He then rattled off 20 blank rounds at full auto. No practical use of course, but it shows how much 'choke' is needed to cycle the action.

10-25-2018, 01:22 PM	#1
Feldkanone New User Join Date: Oct 2018 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts	Luger Blank Adapting Hello, Does anyone offer any guidance on adapting a luger for blank adapting? I know it has been done and I have a beater I would like to convert. I know I will need to restrict the barrel and and I believe modify the toggle area to cycle. Thank you!

10-25-2018, 01:25 PM	#2
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,053 Thanks: 1,036 Thanked 3,988 Times in 1,205 Posts	Normally speaking, threading the inside of the barrel from the muzzle end, and installing a suitable plug with a small vent hole will do the trick. Working out the diameter of the vent hole is the hard part. That is how they murder P08 pistols over here for re-enactors, at least.

10-25-2018, 01:39 PM	#3
Feldkanone New User Join Date: Oct 2018 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts	Yes, but doesn't the action need to be modified so that it will cycle just from the pressure created by the barrel plug? Won't it stay locked without the normal recoil from a live round?

10-25-2018, 02:41 PM	#4
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,053 Thanks: 1,036 Thanked 3,988 Times in 1,205 Posts	The pressure needed to cycle the gun should be generated by the plug with vent hole itself. Similar systems have been used for years as gov't training adaptors. I have shot a 9mm uzi with blanks and a barrel adaptor, these were fitted over the muzzle. AR15's had similar adaptors fitted. All with the same basic principle: reduce muzzle size to increase gas pressure to facilitate cycling on a blank.

10-25-2018, 04:05 PM	#5
Diver6106 User Join Date: Sep 2014 Location: Mt. Vernon VA Posts: 244 Thanks: 1,424 Thanked 117 Times in 75 Posts	If the blanks have a very reduced load of powder, such as not cycling with a fully blocked barrel, you might need to get a weaker main spring for the toggle. Or you could shorten the existing spring to weaken it, by clipping loops off. Or even better - just get a cap pistol.