Barrel tightnening?

lemmonhead · 11-11-2019, 02:09 AM

I recently purchased a number of guns from a shop that will be closing. All of the firearms were in need of some repair. In the group there were 4 Lugers and magazines. Two of the pistols look mostly complete and matching. The other two are mismatched and missing some parts.

One of the pistols, a 1917 ERFURT, has a barrel that is loose. I can remove the barrel by hand. If I tighten the barrel it will stop on time, if it is tightened anymore it will over time. Is there anyway to fix this? Peening or shimming? The barrel looks in fair to good condition.

I have removed and installed numerous rifle barrels, but Lugers are new to me.

DonVoigt · 11-11-2019, 09:28 AM

Peening the flange or a shim- as you say.
A shim that thin will be a bear to make, you will likely need a surface grinder and magnetic table.

With either method, I would add loctite to the threads on final assembly; after confirming headspace is in spec.

If this is not one of the matching pistols, you may want to consider a different barrel, that one does not have the greatest bore anyway; of course that would mean having several barrels to choose from for fit.

Lugerdoc or GT could help you with a different barrel.

lemmonhead · 11-11-2019, 11:07 AM

Quote:

Originally Posted by DonVoigt

Peening the flange or a shim- as you say.
A shim that thin will be a bear to make, you will likely need a surface grinder and magnetic table.

With either method, I would add loctite to the threads on final assembly; after confirming headspace is in spec.

If this is not one of the matching pistols, you may want to consider a different barrel, that one does not have the greatest bore anyway; of course that would mean having several barrels to choose from for fit.

Lugerdoc or GT could help you with a different barrel.

Thanks. From initial observation it appears to be all matching. Even though the bore is not in the best of condition, it would be nice to keep the original barrel if it can be fixed properly.

ithacaartist · 11-11-2019, 11:00 PM

Something thin to take up space might also a be a bead of silver solder, or one laid down by micro-welding. Unless I'm mistaken, peening can squish again. And I agree that making a shim that thin would be next to impossible. Extending or adhering something permanently to the bearing surface of the flange, then facing it off on a lathe until it's just right would be my first choice. Loc-Tite might also do the job by itself if it clocks close enough. I've heard that 1/8 turn with the wrench setup after the hand tightening bottoms out is about right. If the barrel will hand tighten beyond proper position, though, I'd nix the Loc-Tite only approach.

G.T. · 11-12-2019, 08:55 AM

Hi David, you're mostly right, but the correct repair doesn't involve any type of welding, or heating, etc.
What one does is cut a .020" shim, which is thick enough to stand the finishing torque and restore the correct indexing, (1/8" as you describe is about perfect). Then you cut the barrel flange back approx. .010" or so and then assemble with the shim in the normal way... best to all, til….lat'r....GT.....

11-11-2019, 02:09 AM	#1
lemmonhead User Join Date: Nov 2017 Location: Las Vegas Posts: 13 Thanks: 7 Thanked 0 Times in 0 Posts	Barrel tightnening? I recently purchased a number of guns from a shop that will be closing. All of the firearms were in need of some repair. In the group there were 4 Lugers and magazines. Two of the pistols look mostly complete and matching. The other two are mismatched and missing some parts. One of the pistols, a 1917 ERFURT, has a barrel that is loose. I can remove the barrel by hand. If I tighten the barrel it will stop on time, if it is tightened anymore it will over time. Is there anyway to fix this? Peening or shimming? The barrel looks in fair to good condition. I have removed and installed numerous rifle barrels, but Lugers are new to me. Attached Thumbnails

11-11-2019, 09:28 AM	#2
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,442 Thanked 4,350 Times in 2,040 Posts	Peening the flange or a shim- as you say. A shim that thin will be a bear to make, you will likely need a surface grinder and magnetic table. With either method, I would add loctite to the threads on final assembly; after confirming headspace is in spec. If this is not one of the matching pistols, you may want to consider a different barrel, that one does not have the greatest bore anyway; of course that would mean having several barrels to choose from for fit. Lugerdoc or GT could help you with a different barrel. __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

11-11-2019, 11:00 PM	#4
ithacaartist Twice a Lifer Lifetime Forum Patron Join Date: Mar 2011 Location: Atop the highest hill in Schuyler County NY Posts: 3,347 Thanks: 7,285 Thanked 2,579 Times in 1,366 Posts	Something thin to take up space might also a be a bead of silver solder, or one laid down by micro-welding. Unless I'm mistaken, peening can squish again. And I agree that making a shim that thin would be next to impossible. Extending or adhering something permanently to the bearing surface of the flange, then facing it off on a lathe until it's just right would be my first choice. Loc-Tite might also do the job by itself if it clocks close enough. I've heard that 1/8 turn with the wrench setup after the hand tightening bottoms out is about right. If the barrel will hand tighten beyond proper position, though, I'd nix the Loc-Tite only approach. __________________ "... Liberty is the seed and soil, the air and light, the dew and rain of progress, love and joy."-- Robert Greene Ingersoll 1894

11-12-2019, 08:55 AM	#5
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,507 Thanks: 1,318 Thanked 3,653 Times in 1,004 Posts	how to do it? Hi David, you're mostly right, but the correct repair doesn't involve any type of welding, or heating, etc. What one does is cut a .020" shim, which is thick enough to stand the finishing torque and restore the correct indexing, (1/8" as you describe is about perfect). Then you cut the barrel flange back approx. .010" or so and then assemble with the shim in the normal way... best to all, til….lat'r....GT.....