P08 Trigger Problem

wisgro123 · 03-06-2012, 10:23 PM

I removed the barrel and receiver from my P08 to lubricate the slide. I reassembled the pistol after oiling and cocked it. I had to pull the trigger twice before the firing pin activated. I cocked it a few more times and the pin activated each time with one pull but the next time I cocked it I had to pull the trigger twice before the pin activated. I disassembled the barrel and receiver to check but didn't see anything out of order. Reassembled the pistol, cocked it and the pin activated. Cocked it again and had to pull the trigger twice. I tried about a half dozen more times but had to pull the trigger twice at random times. Any suggestions greatly appreciated.

lugersrkewl · 03-06-2012, 10:35 PM

Is the safety on?

wisgro123 · 03-07-2012, 08:53 AM

Thanks for responding so quickly. The pistol won't fire at all with the safety on so I know that's working.

kmichaels90 · 03-07-2012, 09:00 AM

Quote:

Originally Posted by wisgro123

Thanks for responding so quickly. The pistol won't fire at all with the safety on so I know that's working.

On the end of the sear bar at the front is a spring plunger that acts as the disconnector. When you fire the gun and it returns to battery this plunger is compressed by the trigger bar in the sideplate. When you release the trigger this plunger pops out behind the trigger bar so that it can contact it when you fire the next shot. It sounds like this plunger is not popping out when you release the trigger therefore not allowing the gun to fire. If you remove the sideplate and look at how it is linked to the trigger and sear bar you will see what im talking about.

wisgro123 · 03-07-2012, 09:09 AM

Great. Thanks. I'll check it out later today.

alvin · 03-06-2012, 11:06 PM

Sounds like trigger bar plunger pin's issue. This plunger is the key component of Luger's disconnecting mechanism.

wisgro123 · 03-07-2012, 08:52 AM

Thanks for responding so quickly. You said "trigger bar plunger pin." Do you mean the Sear Bar Spring?

alanint · 03-06-2012, 11:30 PM

Agreed. The plunger at the end of the sear bar is not resetting properly after each firing sequence.

wisgro123 · 03-07-2012, 08:51 AM

Thanks for responding so quickly. Do you mean the Sear Bar Spring when you say the plunger?

Lugerdoc · 03-07-2012, 10:44 AM

W, I'd first check that you have the side plate properly inserted into the notch in the frame and that it is flush with the frame. If so, then you probably will have to do some work on the trigger lever inside the side plate, for correct resetting of the disconnector plunger. TH

wisgro123 · 03-07-2012, 11:24 AM

Thanks for responding. Before I checked the side plate fit I put a drop of oil at the axle pin where it goes through the lever in the back of the side plate. I then carefully inserted the plate into the notch. (I took it off and replaced it a few times, checking carefully for fit.) If I hold the pistol so that I am facing the muzzle I can see a small gap between the side plate and side of the receiver. I can slide 3 thicknesses of regular bond paper edgewise into the gap (about 1/64). I can press the side plate snugly to the receiver but it doesn't stay there. Pressing the side plate before pulling the trigger doesn't help. I then cocked and pulled the trigger very slowly. Feels like something is not operating smoothly, like an obstruction then fires. Unfortunately when I cocked it again I had to pull the trigger 3 times before it fired.

wisgro123 · 03-07-2012, 02:52 PM

Have followed everyone's suggestion without success. The last suggestion was to push the muzzle back, press and hold the trigger, release the barrel then slowly pull the trigger and I should hear a click. I tried a couple of times didn't hear a click. I took the side plate from my other Luger that works fine and installed it on the problem pistol. The problem was still there. You mentioned I would have to do some work on the trigger lever inside the side plate. What do you suggest? I looked at the side plate of my working pistol and the action, how far the lever moves, etc. looks identical.

kmichaels90 · 03-07-2012, 11:40 AM

Did you check the plunger on the sear bar to see if it is indeed sticking in and popping out slowly?

wisgro123 · 03-07-2012, 11:48 AM

Yes I checked that. It works fine with the trigger side plate off but it's covered when I replace the side plate so I can't see the action. I put a drop of oil on and worked the plunger quite a few times before replacing the side plate but that didn't help.

kmichaels90 · 03-07-2012, 11:58 AM

Seems very odd. If you have the gun cocked with it assembled then remove the upper will it release the firing pin when pressure is applied to the sear bar? If not I would say the issue is with the sear bar or firing pin. If it does release I would think the problem is in the trigger/sideplate/sear bar engagement. That would be an area where I wouldnt know what to do.

wisgro123 · 03-07-2012, 12:11 PM

I agree it's odd. The pistol has been handled carefully. Just took it out for a periodic wipe down and ran into a brick wall. Could you please explain what you mean by "remove the upper." What part are you referring to? (I looked at the P08 disassemble video and noticed that when the demonstrator pulls the toggle back to **** the pistol the toggle stays up by itself. I have 3 P08s and the toggle doesn't stay up on any of them.)

kmichaels90 · 03-07-2012, 12:20 PM

You very likely have 3 p08's like my p08 which does not have a last shot hold open. What I mean is make sure it is cocked, then remove the sideplate and slide the upper assembly (barrel,receiver,toggle assembly) off the front of the frame. Now push on the sear bar toward the barrel end and see if it releases the firing pin. If so I think you have an issue with your sideplate. If it doest release I'd say the issue is with the sear bar or firing pin.

wisgro123 · 03-07-2012, 12:41 PM

I followed your directions. The sear bar doesn't move and the firing pin is not released. The plunger located in the front of the sear bar pushes back easily. It springs forward into position when I release it. I reassembled the barrel, receiver and toggle assembly and pulled the trigger. I then disassembled the same parts and tried to push the sear bar. It won't move in either direction. (I have a parts map with labels so I can be sure I'm identifying the correct parts.) Should I be able to move the bar? Do you still think it's the sear bar or firing pin?

kmichaels90 · 03-07-2012, 12:51 PM

Quote:

Originally Posted by wisgro123

I followed your directions. The sear bar doesn't move and the firing pin is not released. The plunger located in the front of the sear bar pushes back easily. It springs forward into position when I release it. I reassembled the barrel, receiver and toggle assembly and pulled the trigger. I then disassembled the same parts and tried to push the sear bar. It won't move in either direction. (I have a parts map with labels so I can be sure I'm identifying the correct parts.) Should I be able to move the bar? Do you still think it's the sear bar or firing pin?

Hmm... when pushing the sear bar you should be pushing the front half of it towards the other side of the gun. Such as put your thumbnail on the side of the plunger and push it in towards the center of the receiver. If thats what you did and it wont release it sounds like something is binding.

wisgro123 · 03-07-2012, 01:04 PM

Yes I pushed the bar the way you described and the firing pin released. I noticed the spring on the back of the trigger is compressed so I took the trigger and side plate from a pistol that works fine and installed it on the faulty pistol and the same problem happens. Doesn't that eliminate the side plate and trigger?

03-06-2012, 10:23 PM	#1
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	P08 Trigger Problem I removed the barrel and receiver from my P08 to lubricate the slide. I reassembled the pistol after oiling and cocked it. I had to pull the trigger twice before the firing pin activated. I cocked it a few more times and the pin activated each time with one pull but the next time I cocked it I had to pull the trigger twice before the pin activated. I disassembled the barrel and receiver to check but didn't see anything out of order. Reassembled the pistol, cocked it and the pin activated. Cocked it again and had to pull the trigger twice. I tried about a half dozen more times but had to pull the trigger twice at random times. Any suggestions greatly appreciated.

03-07-2012, 10:44 AM	#10
Lugerdoc Patron LugerForum Patron Join Date: Jun 2002 Location: POB 398 St.Charles,MO. 63302 Posts: 5,089 Thanks: 6 Thanked 736 Times in 483 Posts	W, I'd first check that you have the side plate properly inserted into the notch in the frame and that it is flush with the frame. If so, then you probably will have to do some work on the trigger lever inside the side plate, for correct resetting of the disconnector plunger. TH __________________ Tom Heller POB 398 ST.Charles, MO. 63302 Tel 636-447-3006 [email protected]

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

03-06-2012, 10:35 PM	#2
lugersrkewl Patron LugerForum Patron Join Date: Feb 2012 Location: Ussr Posts: 425 Thanks: 198 Thanked 75 Times in 58 Posts	Is the safety on?

03-07-2012, 08:53 AM	#3
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Thanks for responding so quickly. The pistol won't fire at all with the safety on so I know that's working.

03-07-2012, 09:09 AM	#5
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Great. Thanks. I'll check it out later today.

03-06-2012, 11:06 PM	#6
alvin User Join Date: Jul 2007 Location: US Posts: 3,843 Thanks: 132 Thanked 729 Times in 438 Posts	Sounds like trigger bar plunger pin's issue. This plunger is the key component of Luger's disconnecting mechanism.

03-07-2012, 08:52 AM	#7
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Thanks for responding so quickly. You said "trigger bar plunger pin." Do you mean the Sear Bar Spring?

03-06-2012, 11:30 PM	#8
alanint User Join Date: Mar 2008 Location: Marco Island, Florida Posts: 4,867 Thanks: 1,685 Thanked 1,916 Times in 1,192 Posts	Agreed. The plunger at the end of the sear bar is not resetting properly after each firing sequence.

03-07-2012, 08:51 AM	#9
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Thanks for responding so quickly. Do you mean the Sear Bar Spring when you say the plunger?

03-07-2012, 11:24 AM	#11
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Thanks for responding. Before I checked the side plate fit I put a drop of oil at the axle pin where it goes through the lever in the back of the side plate. I then carefully inserted the plate into the notch. (I took it off and replaced it a few times, checking carefully for fit.) If I hold the pistol so that I am facing the muzzle I can see a small gap between the side plate and side of the receiver. I can slide 3 thicknesses of regular bond paper edgewise into the gap (about 1/64). I can press the side plate snugly to the receiver but it doesn't stay there. Pressing the side plate before pulling the trigger doesn't help. I then cocked and pulled the trigger very slowly. Feels like something is not operating smoothly, like an obstruction then fires. Unfortunately when I cocked it again I had to pull the trigger 3 times before it fired.

03-07-2012, 02:52 PM	#12
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Have followed everyone's suggestion without success. The last suggestion was to push the muzzle back, press and hold the trigger, release the barrel then slowly pull the trigger and I should hear a click. I tried a couple of times didn't hear a click. I took the side plate from my other Luger that works fine and installed it on the problem pistol. The problem was still there. You mentioned I would have to do some work on the trigger lever inside the side plate. What do you suggest? I looked at the side plate of my working pistol and the action, how far the lever moves, etc. looks identical.

03-07-2012, 11:40 AM	#13
kmichaels90 User Join Date: Mar 2012 Location: Bucyrus OH Posts: 60 Thanks: 1 Thanked 7 Times in 7 Posts	Did you check the plunger on the sear bar to see if it is indeed sticking in and popping out slowly?

03-07-2012, 11:48 AM	#14
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Yes I checked that. It works fine with the trigger side plate off but it's covered when I replace the side plate so I can't see the action. I put a drop of oil on and worked the plunger quite a few times before replacing the side plate but that didn't help.

03-07-2012, 11:58 AM	#15
kmichaels90 User Join Date: Mar 2012 Location: Bucyrus OH Posts: 60 Thanks: 1 Thanked 7 Times in 7 Posts	Seems very odd. If you have the gun cocked with it assembled then remove the upper will it release the firing pin when pressure is applied to the sear bar? If not I would say the issue is with the sear bar or firing pin. If it does release I would think the problem is in the trigger/sideplate/sear bar engagement. That would be an area where I wouldnt know what to do.

03-07-2012, 12:11 PM	#16
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	I agree it's odd. The pistol has been handled carefully. Just took it out for a periodic wipe down and ran into a brick wall. Could you please explain what you mean by "remove the upper." What part are you referring to? (I looked at the P08 disassemble video and noticed that when the demonstrator pulls the toggle back to **** the pistol the toggle stays up by itself. I have 3 P08s and the toggle doesn't stay up on any of them.)

03-07-2012, 12:20 PM	#17
kmichaels90 User Join Date: Mar 2012 Location: Bucyrus OH Posts: 60 Thanks: 1 Thanked 7 Times in 7 Posts	You very likely have 3 p08's like my p08 which does not have a last shot hold open. What I mean is make sure it is cocked, then remove the sideplate and slide the upper assembly (barrel,receiver,toggle assembly) off the front of the frame. Now push on the sear bar toward the barrel end and see if it releases the firing pin. If so I think you have an issue with your sideplate. If it doest release I'd say the issue is with the sear bar or firing pin.

03-07-2012, 12:41 PM	#18
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	I followed your directions. The sear bar doesn't move and the firing pin is not released. The plunger located in the front of the sear bar pushes back easily. It springs forward into position when I release it. I reassembled the barrel, receiver and toggle assembly and pulled the trigger. I then disassembled the same parts and tried to push the sear bar. It won't move in either direction. (I have a parts map with labels so I can be sure I'm identifying the correct parts.) Should I be able to move the bar? Do you still think it's the sear bar or firing pin?

03-07-2012, 01:04 PM	#20
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	Yes I pushed the bar the way you described and the firing pin released. I noticed the spring on the back of the trigger is compressed so I took the trigger and side plate from a pistol that works fine and installed it on the faulty pistol and the same problem happens. Doesn't that eliminate the side plate and trigger?