P08 Trigger Problem Solved!

wisgro123 · 03-08-2012, 03:19 PM

Thanks to all of you folks I figured there should be no gap between the side plate and slide. If I pretend I have 3 hands I might be able to eliminate the gap thusly: 1. Press and hold the side plate against the slide as hard as possible to eliminate the gap. 2. Press the muzzle toward the back of the pistol. 3. Slide the locking bolt up 90 degrees to lock the side plate in place.
4. Dry fire the pistol over a dozen times without a miss. Problem solved.

kmichaels90 · 03-08-2012, 07:44 PM

Sounds like something might be slightly out of whack somewhere but I'm glad you got it working. I have read that its not good on a luger to dryfire it w/o a snap cap or spent casing in the chamber but I doubt you hurt anything only doing it a few times.

MikeP · 03-09-2012, 02:28 AM

I have one that some fool used a screwdriver to try and pry off the sideplate.
He did it just enough that there is a tiny gap visible and a teeny "twist" on the tab.
It sometimes won't fire.
I see the problem but not willing to "untwist" the problem, possibly creating a bigger one.
I have dry fired an awful lot of Lugers in 50+ years without a problem.
I should stop it someday.

John Sabato · 03-09-2012, 04:58 PM

This gap is repairable... but not recommended for an amateur... Send it to Lugerdoc, Thor or Hugh Clark for repair...

03-08-2012, 03:19 PM	#1
wisgro123 User Join Date: Aug 2008 Posts: 24 Thanks: 16 Thanked 0 Times in 0 Posts	P08 Trigger Problem Solved! Thanks to all of you folks I figured there should be no gap between the side plate and slide. If I pretend I have 3 hands I might be able to eliminate the gap thusly: 1. Press and hold the side plate against the slide as hard as possible to eliminate the gap. 2. Press the muzzle toward the back of the pistol. 3. Slide the locking bolt up 90 degrees to lock the side plate in place. 4. Dry fire the pistol over a dozen times without a miss. Problem solved.

03-09-2012, 04:58 PM	#4
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,154 Thanks: 3,003 Thanked 2,306 Times in 1,097 Posts	This gap is repairable... but not recommended for an amateur... Send it to Lugerdoc, Thor or Hugh Clark for repair... __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-08-2012, 07:44 PM	#2
kmichaels90 User Join Date: Mar 2012 Location: Bucyrus OH Posts: 60 Thanks: 1 Thanked 7 Times in 7 Posts	Sounds like something might be slightly out of whack somewhere but I'm glad you got it working. I have read that its not good on a luger to dryfire it w/o a snap cap or spent casing in the chamber but I doubt you hurt anything only doing it a few times.

03-09-2012, 02:28 AM	#3
MikeP User Join Date: Jun 2002 Location: ILL Posts: 686 Thanks: 36 Thanked 452 Times in 198 Posts	I have one that some fool used a screwdriver to try and pry off the sideplate. He did it just enough that there is a tiny gap visible and a teeny "twist" on the tab. It sometimes won't fire. I see the problem but not willing to "untwist" the problem, possibly creating a bigger one. I have dry fired an awful lot of Lugers in 50+ years without a problem. I should stop it someday.