My Luger Project

The Wizard · 03-30-2002, 12:25 AM

I have a Mauser-Parabellum '06/73' "American Eagle" in 7.65 mm Parabellum with a 150 mm barrel. What I would like to do is switch out the 150 mm barrel with a 120 mm barrel like to one use on the Mauser-Parabellum '06/73' Bulgaria and Swiss Commemoratives. Now the easiest way to do this is to find a Mauser made spare barrel and do a remove and replace. Does anyone know if Mauser has spare parts for thier pistols? If I had the engineering drawing of the barrel I could fabricate one but I do not think Mauser would release that information to me.

One other thing, anyone know a Mauser Broomhandle expert. I have a Model 1930 Broomhandle that I can not rmove the magazine floor plate. No obivous damage but a real tight fit.

Well, thank you for your time and effort.

The Wizard

Lonnie Zimmerman · 03-30-2002, 01:20 AM

On the Broomhandle floorplate, push down on the button with some non maring (sic) tool, and pull foreward on plate. Works for me.

Lonnie

Frank · 03-30-2002, 10:19 AM

If Lonnie's method doesn't work on your Broomhandle, you might try Kyrie Ellis or Tom Heller. Thier email addresses should be in the Profile Section! Good Luck!

03-30-2002, 10:43 AM

Wizard, On your broom, you may have to use I stong pin punch at a 45 degree angle, hitting floor plate forward at the same time that it depresses release button. Since I purchased all of Interarms Mauser Parabellum parts and know that Mauser doesn't have any barrel left in Germany, your best bet would be to find a nice bore M1906 LONG FRAME 120mm barrel for this project. All of the long frame ones that I have left are M1900, so the extractor cut would also have to be modified. Tom h.

Kyrie · 03-30-2002, 08:24 PM

Hi Wizard,

If you continue to have problems with the C96 e-mail me off line and I'll try and help....

Best regards,

Kyrie

03-31-2002, 12:54 PM

is not my cup of tea, although I do have acopy of all of the metric dimentions of the the 9X100mm military barrels as shown in the original 1913 Masstafeln zur PO8. I believe one of the members is offering the drawing of all PO8 parts from this book on CD at a reasonable price in the "links & resources" section. Tom h.

HÃ?Â¥kan Spuhr · 03-31-2002, 08:16 PM

I sold a very good swiss 06/29 barrel to Hugh some time ago.

Check with him if he have it left in that case you can use thatone.

Regards HÃ?Â¥kan

http://www.vapensmedjan.com

03-30-2002, 12:25 AM	#1
The Wizard User Join Date: Jun 2002 Location: Colorado Springs, Colorado Posts: 67 Thanks: 0 Thanked 0 Times in 0 Posts	My Luger Project I have a Mauser-Parabellum '06/73' "American Eagle" in 7.65 mm Parabellum with a 150 mm barrel. What I would like to do is switch out the 150 mm barrel with a 120 mm barrel like to one use on the Mauser-Parabellum '06/73' Bulgaria and Swiss Commemoratives. Now the easiest way to do this is to find a Mauser made spare barrel and do a remove and replace. Does anyone know if Mauser has spare parts for thier pistols? If I had the engineering drawing of the barrel I could fabricate one but I do not think Mauser would release that information to me. One other thing, anyone know a Mauser Broomhandle expert. I have a Model 1930 Broomhandle that I can not rmove the magazine floor plate. No obivous damage but a real tight fit. Well, thank you for your time and effort. The Wizard

03-30-2002, 01:20 AM	#2
Lonnie Zimmerman User Join Date: Jun 2002 Posts: 523 Thanks: 0 Thanked 1 Time in 1 Post	Re: My Luger Project On the Broomhandle floorplate, push down on the button with some non maring (sic) tool, and pull foreward on plate. Works for me. Lonnie

03-30-2002, 10:19 AM	#3
Frank RIP Patron LugerForum Patron Join Date: Jun 2002 Location: Hot & Dry PHX, AZ Posts: 2,078 Thanks: 24 Thanked 163 Times in 87 Posts	Re: My Luger Project If Lonnie's method doesn't work on your Broomhandle, you might try Kyrie Ellis or Tom Heller. Thier email addresses should be in the Profile Section! Good Luck!

03-30-2002, 10:43 AM	#4
tom h Guest Posts: n/a	Re: My Luger Project Wizard, On your broom, you may have to use I stong pin punch at a 45 degree angle, hitting floor plate forward at the same time that it depresses release button. Since I purchased all of Interarms Mauser Parabellum parts and know that Mauser doesn't have any barrel left in Germany, your best bet would be to find a nice bore M1906 LONG FRAME 120mm barrel for this project. All of the long frame ones that I have left are M1900, so the extractor cut would also have to be modified. Tom h.

03-30-2002, 08:24 PM	#5
Kyrie User Join Date: Jun 2002 Posts: 757 Thanks: 0 Thanked 212 Times in 101 Posts	Re: My Luger Project Hi Wizard, If you continue to have problems with the C96 e-mail me off line and I'll try and help.... Best regards, Kyrie

03-31-2002, 12:54 PM	#6
tom h Guest Posts: n/a	Re: Barrel design is not my cup of tea, although I do have acopy of all of the metric dimentions of the the 9X100mm military barrels as shown in the original 1913 Masstafeln zur PO8. I believe one of the members is offering the drawing of all PO8 parts from this book on CD at a reasonable price in the "links & resources" section. Tom h.

03-31-2002, 08:16 PM	#7
HÃ?Â¥kan Spuhr User Join Date: Jun 2002 Location: Sweden Posts: 282 Thanks: 0 Thanked 0 Times in 0 Posts	Re: My Luger Project I sold a very good swiss 06/29 barrel to Hugh some time ago. Check with him if he have it left in that case you can use thatone. Regards HÃ?Â¥kan http://www.vapensmedjan.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode