Kreighoff firing pin protrusion gage

DonVoigt · 06-25-2017, 09:49 PM

My friend Tim loaned me his Kreighoff gage so I could make a gage for myself.

Thought all would like to see the gage.

Firing pin protrusion from the bolt face specs are between 1.1mm(min) and 1.35mm(max).

The 1.1mm side of the gage is placed against the breech block to the side of the firing pin, the pin must not pass under the cut out; if it does it is too short.
Flip the gage around, and the 1.35mm side should pass over the firing pin, if it does not - it is too long.

A long pin tip can be stoned to shorten it, the tip should also be nicely rounded, not "pointy".

Also shown is one of the gages I made in similar pattern; I chose to "straw" mine.

lugerholsterrepair · 06-26-2017, 12:21 AM

Don, I don't mean to pick a nit here but they don't look the same?

Is the overall original pattern profile important to inserting the tool into the pistol for measurement? Or is this measured with the bolt out?

What is the round notch at the top for?

DonVoigt · 06-26-2017, 10:24 AM

Jerry,
the overall profile is a little different and does not matter, the tool is grasped in the center area- it is only either end that is used. I could have reduced the width with two more milling cuts, but it would have been a waste of time for me; I left "mine" the width of the stock I used. It is meant to be used, not a "reproduction".

It is used with the toggle/bolt out; with the toggle in and back- the striker/firing pin is retracted.

I have no idea why there is a notch at the top, Tim had two HK tools, the notches were in both, but they were different sizes. We surmised that they were a fixturing notch for use in mfg.???

Good eye and good questions; I glad someone read the post!

lugerholsterrepair · 06-26-2017, 01:22 PM

Don, Well very cool anyway..It's a fairly simple thing but seems important to check? Pierced primers, misfires and all that!

Thanks for the edumacation..I could have reduced the width with two minutes on my giant bubba bench grinder..two more milling cuts? La TI DA!

Anyway good job! If I can find time I might hack one out with my grinder and a hack saw..might use a bastard file if I want it purty. But leather calls...

DonVoigt · 06-26-2017, 10:01 PM

Quote:

Originally Posted by lugerholsterrepair

Don, Well very cool anyway..It's a fairly simple thing but seems important to check? Pierced primers, misfires and all that!

Thanks for the edumacation..I could have reduced the width with two minutes on my giant bubba bench grinder..two more milling cuts? La TI DA!

Anyway good job! If I can find time I might hack one out with my grinder and a hack saw..might use a bastard file if I want it purty. But leather calls...

Yes, only 2 more, but after 10 already - I was done!

As I said the width at that point is irrelevant- wider is actually an "improvement" if you have fat fingers.

g5m · 05-04-2018, 11:24 PM

Could you give the dimensions? I might want to make one instead of buying an original.

Vlim · 05-05-2018, 06:46 AM

I have 2 East German ones here. No notch on the top.

Vlim · 05-05-2018, 06:51 AM

Note that the firing pin gauge is numbered 2 207.

This chamber gauge, 8.88mm, is numberef 2 206.

06-25-2017, 09:49 PM	#1
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,442 Thanked 4,350 Times in 2,040 Posts	Kreighoff firing pin protrusion gage My friend Tim loaned me his Kreighoff gage so I could make a gage for myself. Thought all would like to see the gage. Firing pin protrusion from the bolt face specs are between 1.1mm(min) and 1.35mm(max). The 1.1mm side of the gage is placed against the breech block to the side of the firing pin, the pin must not pass under the cut out; if it does it is too short. Flip the gage around, and the 1.35mm side should pass over the firing pin, if it does not - it is too long. A long pin tip can be stoned to shorten it, the tip should also be nicely rounded, not "pointy". Also shown is one of the gages I made in similar pattern; I chose to "straw" mine. Attached Thumbnails __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

06-26-2017, 12:21 AM	#2
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	Don, I don't mean to pick a nit here but they don't look the same? Is the overall original pattern profile important to inserting the tool into the pistol for measurement? Or is this measured with the bolt out? What is the round notch at the top for? __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

06-26-2017, 10:24 AM	#3
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,681 Thanks: 1,442 Thanked 4,350 Times in 2,040 Posts	Jerry, the overall profile is a little different and does not matter, the tool is grasped in the center area- it is only either end that is used. I could have reduced the width with two more milling cuts, but it would have been a waste of time for me; I left "mine" the width of the stock I used. It is meant to be used, not a "reproduction". It is used with the toggle/bolt out; with the toggle in and back- the striker/firing pin is retracted. I have no idea why there is a notch at the top, Tim had two HK tools, the notches were in both, but they were different sizes. We surmised that they were a fixturing notch for use in mfg.??? Good eye and good questions; I glad someone read the post! __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

06-26-2017, 01:22 PM	#4
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	Don, Well very cool anyway..It's a fairly simple thing but seems important to check? Pierced primers, misfires and all that! Thanks for the edumacation..I could have reduced the width with two minutes on my giant bubba bench grinder..two more milling cuts? La TI DA! Anyway good job! If I can find time I might hack one out with my grinder and a hack saw..might use a bastard file if I want it purty. But leather calls... __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

05-04-2018, 11:24 PM	#6
g5m User Join Date: Apr 2018 Location: desert Posts: 36 Thanks: 23 Thanked 5 Times in 5 Posts	Could you give the dimensions? I might want to make one instead of buying an original. Last edited by g5m; 05-05-2018 at 12:56 AM.

05-05-2018, 06:46 AM	#7
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,053 Thanks: 1,036 Thanked 3,989 Times in 1,205 Posts	I have 2 East German ones here. No notch on the top. Attached Thumbnails

05-05-2018, 06:51 AM	#8
Vlim Moderator Lifetime LugerForum Patron Join Date: Oct 2002 Location: Europe Posts: 5,053 Thanks: 1,036 Thanked 3,989 Times in 1,205 Posts	Note that the firing pin gauge is numbered 2 207. This chamber gauge, 8.88mm, is numberef 2 206. Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode