Help Identifying Inherited Luger

bloungo · 07-26-2023, 11:44 AM

I recently inherited a Luger and would appreciate any help in identifying it. Attached are photos of the markings I could find.

Mac Cat · 07-26-2023, 12:14 PM

Welcome to the Forum.
Thanks for sharing your luger

What have you found out about it, so far?

Was there a story about where it came from?

rhuff · 07-26-2023, 03:43 PM

It is obviously a "parts" Luger....made up of different parts from different Lugers. I believe that parts of it have been refinished. It should make a good shooter, but not a collector piece. Congrats!!

bloungo · 07-26-2023, 10:47 PM

What makes it a parts Luger? All the numbers seem to match.

reiver · 07-26-2023, 11:15 PM

All of the parts should have 44 on them not 59...the last two digits of the Serial number on the frame. The toggle assembly does not match the frame number. It is a parts pistol.

Given that it is mismatched and seriously pitted and re blued it is on the bottom end of the shooter class.... not an heirloom. If you attempted to sell it, well, no idea but it would go on the cheap side.

Karl · 07-27-2023, 12:20 PM

Bloungo,

It appears from your photographs that the retaining pin for the rear toggle pin is missing. I suggest that you check this and rectify any problem before attempting to fire the gun.

Karl

Doubs · 07-27-2023, 05:08 PM

It's a military Luger that has been refinished using parts from different pistols. The notch at the front of the receiver shows that the receiver was on either a DWM Artillery Luger or a 1914 Erfurt Artillery Luger or a 1916 ~ 1918 Erfurt short barrel Luger. The date and proof/inspection stamps have been scrubbed so there's no way to tell.

The toggle train - or parts of it - are Erfurt while the frame is DWM. Your Luger falls into the shooter grade category. It has no collector value but if you inherited it, the sentimental value may outweigh all other considerations... as it should.

07-26-2023, 11:44 AM	#1
bloungo New User Join Date: Jul 2023 Posts: 2 Thanks: 0 Thanked 2 Times in 1 Post	Help Identifying Inherited Luger I recently inherited a Luger and would appreciate any help in identifying it. Attached are photos of the markings I could find. Attached Thumbnails

07-26-2023, 03:43 PM	#3
rhuff Patron LugerForum Patron Join Date: Mar 2011 Location: Az. Posts: 2,291 Thanks: 2,709 Thanked 972 Times in 717 Posts	It is obviously a "parts" Luger....made up of different parts from different Lugers. I believe that parts of it have been refinished. It should make a good shooter, but not a collector piece. Congrats!! __________________ Need DWM breechblock #21

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-26-2023, 12:14 PM	#2
Mac Cat Lifer Lifetime Forum Patron Join Date: Apr 2015 Location: Austin, Texas Posts: 731 Thanks: 2,095 Thanked 610 Times in 329 Posts	Welcome to the Forum. Thanks for sharing your luger What have you found out about it, so far? Was there a story about where it came from?

07-26-2023, 10:47 PM	#4
bloungo New User Join Date: Jul 2023 Posts: 2 Thanks: 0 Thanked 2 Times in 1 Post	What makes it a parts Luger? All the numbers seem to match.

07-26-2023, 11:15 PM	#5
reiver User Join Date: Feb 2023 Posts: 132 Thanks: 81 Thanked 149 Times in 63 Posts	All of the parts should have 44 on them not 59...the last two digits of the Serial number on the frame. The toggle assembly does not match the frame number. It is a parts pistol. Given that it is mismatched and seriously pitted and re blued it is on the bottom end of the shooter class.... not an heirloom. If you attempted to sell it, well, no idea but it would go on the cheap side.

07-27-2023, 12:20 PM	#6
Karl Lifer - Twice Over Lifetime Forum Patron Join Date: Jun 2002 Location: Savannah Posts: 522 Thanks: 0 Thanked 271 Times in 118 Posts	Bloungo, It appears from your photographs that the retaining pin for the rear toggle pin is missing. I suggest that you check this and rectify any problem before attempting to fire the gun. Karl

07-27-2023, 05:08 PM	#7
Doubs User Join Date: Jun 2002 Location: Byron, Georgia Posts: 1,698 Thanks: 792 Thanked 1,687 Times in 554 Posts	It's a military Luger that has been refinished using parts from different pistols. The notch at the front of the receiver shows that the receiver was on either a DWM Artillery Luger or a 1914 Erfurt Artillery Luger or a 1916 ~ 1918 Erfurt short barrel Luger. The date and proof/inspection stamps have been scrubbed so there's no way to tell. The toggle train - or parts of it - are Erfurt while the frame is DWM. Your Luger falls into the shooter grade category. It has no collector value but if you inherited it, the sentimental value may outweigh all other considerations... as it should.