ANOTHER NEW LUGER OWNER

Jeff · 10-03-2002, 08:13 PM

MY DAD GAVE ME A 1916 ERFURT LUGER HE GOT IN 1946, BROUGHT BACK FROM GERMANY. THE SERIAL# IS 4, ALL THE PARTS HAVE THE #4 ON THEM EXCEPT THE SIDE PLATE WHICH IS BLANK. I HAVE TWO MAGAZINES, BOTH HAVE WHAT APPEARS AN EAGLE WITH #37 UNDER THE EAGLE ON THE LEFT SIDE. fxo is also on the mag. THE FINISH IS NOT THE BEST MAYBE 50%. THE LOCKING BOLT PIN STICKS OUT THE BOTTOM OF THE FRAME IN FRONT OF THE TRIGGER, I DON'T KNOW WHY, ANY SUGGESTIONS. I WAS ABLE TO PRINT SOME OF THE NOMENCLATURE OF THE PARTS OFF THIS FORUM. THANKS FOR ANY INFO YOU CAN GIVE ME, I ALWAYS LIKED THE WAY THE LUGER PISTOL LOOKED AND FIRED. jeff

Frank · 10-04-2002, 01:59 AM

Hi Jeff, Congratulations on your new Luger!!! The little pin sticking out the bottom of the frame, just in front of the trigger guard is the Locking Bolt Spring end. If this spring protrudes too far, it could be an indication of a deformed or broken spring. These springs will stick out varying amounts on different Lugers.

This little Ã¢??LÃ¢?Â shaped spring is extremely important for the proper operation of the Luger. It prevents the Locking Bolt from rotating to the disassembly position during operation. It should provide some resistance to the rotation of the Locking Block. To examine the spring, rotate the locking block, remove the trigger plate and remove the cannon (receiver) assembly. Then slip the locking block out of the frame, from right to left. The little cavity in the frame below the locking block houses the spring. It can be removed, but just a visual inspection, in place, should show the condition. Make sure it isnÃ¢??t broken. If it isnÃ¢??t broken AND provides a reasonable resistance to the locking block itÃ¢??s good to go.

Good Hunting!!
[img]smile.gif[/img]

Lugerdoc · 10-04-2002, 08:36 AM

It possible that your locking bolt spring has been replaced with one for a long frame luger or more likely one of the 1970s Mauser Parabellums. These springs are about a 32nd" longer. Tom

10-03-2002, 08:13 PM	#1
Jeff User Join Date: Oct 2002 Location: Ohio Posts: 13 Thanks: 0 Thanked 0 Times in 0 Posts	ANOTHER NEW LUGER OWNER MY DAD GAVE ME A 1916 ERFURT LUGER HE GOT IN 1946, BROUGHT BACK FROM GERMANY. THE SERIAL# IS 4, ALL THE PARTS HAVE THE #4 ON THEM EXCEPT THE SIDE PLATE WHICH IS BLANK. I HAVE TWO MAGAZINES, BOTH HAVE WHAT APPEARS AN EAGLE WITH #37 UNDER THE EAGLE ON THE LEFT SIDE. fxo is also on the mag. THE FINISH IS NOT THE BEST MAYBE 50%. THE LOCKING BOLT PIN STICKS OUT THE BOTTOM OF THE FRAME IN FRONT OF THE TRIGGER, I DON'T KNOW WHY, ANY SUGGESTIONS. I WAS ABLE TO PRINT SOME OF THE NOMENCLATURE OF THE PARTS OFF THIS FORUM. THANKS FOR ANY INFO YOU CAN GIVE ME, I ALWAYS LIKED THE WAY THE LUGER PISTOL LOOKED AND FIRED. jeff

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-04-2002, 01:59 AM	#2
Frank RIP Patron LugerForum Patron Join Date: Jun 2002 Location: Hot & Dry PHX, AZ Posts: 2,078 Thanks: 24 Thanked 163 Times in 87 Posts	Hi Jeff, Congratulations on your new Luger!!! The little pin sticking out the bottom of the frame, just in front of the trigger guard is the Locking Bolt Spring end. If this spring protrudes too far, it could be an indication of a deformed or broken spring. These springs will stick out varying amounts on different Lugers. This little Ã¢??LÃ¢?Â shaped spring is extremely important for the proper operation of the Luger. It prevents the Locking Bolt from rotating to the disassembly position during operation. It should provide some resistance to the rotation of the Locking Block. To examine the spring, rotate the locking block, remove the trigger plate and remove the cannon (receiver) assembly. Then slip the locking block out of the frame, from right to left. The little cavity in the frame below the locking block houses the spring. It can be removed, but just a visual inspection, in place, should show the condition. Make sure it isnÃ¢??t broken. If it isnÃ¢??t broken AND provides a reasonable resistance to the locking block itÃ¢??s good to go. Good Hunting!! [img]smile.gif[/img]

10-04-2002, 08:36 AM	#3
Lugerdoc Patron LugerForum Patron Join Date: Jun 2002 Location: POB 398 St.Charles,MO. 63302 Posts: 5,089 Thanks: 6 Thanked 736 Times in 483 Posts	It possible that your locking bolt spring has been replaced with one for a long frame luger or more likely one of the 1970s Mauser Parabellums. These springs are about a 32nd" longer. Tom __________________ Tom Heller POB 398 ST.Charles, MO. 63302 Tel 636-447-3006 [email protected]