Albuquerque this weekend

Ron Wood · 09-27-2005, 06:53 PM

Going to take a break from landscaping this weekend and relax at the Alb. gunshow. I know Bob Adams will be there and John Eckert will set up his display Saturday morning (he is off fishing, I think in Colorado, this week and won't get back till late Friday). Ron Peterson will probably trot out some collectable stuff. Anybody else? Sid? Ted? Don?

Dwight Gruber · 09-27-2005, 08:21 PM

Ron,

Won't be able to be there. But if Bob Adams is, you might see if you can get a serious look at the Test Eagle-sans-Eagle that he has had for sale for a while.

--Dwight

Ron Wood · 09-27-2005, 09:03 PM

I looked at it at last year's show and measured it against my Test Eagles. I agree with Bob that the gun looks like it never had a crest. The chamber area did not look ground, but as I recall it measured .002 to .004 smaller in diameter than mine. I measured at the front of the receiver, half-way back and across the recoil lug. I don't know if that is enough to remove a crest or not. I wrote the measurements down in a little notebook, but I don't know where it is right now. If I find it, I will let you know the measurements.

Strider · 09-28-2005, 03:12 PM

Hi Ron,

I plan on being there on sometime Saturday morning. The Albuquerque Balloon Fiesta starts this weekend so the it should not be to crowded in the morning. Hopefully we will be able to see some good stuff. It will be good to see you again. I will look for you over at Bob's table.

Sid.

09-27-2005, 06:53 PM	#1
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,022 Thanks: 1,090 Thanked 5,179 Times in 1,703 Posts	Albuquerque this weekend Going to take a break from landscaping this weekend and relax at the Alb. gunshow. I know Bob Adams will be there and John Eckert will set up his display Saturday morning (he is off fishing, I think in Colorado, this week and won't get back till late Friday). Ron Peterson will probably trot out some collectable stuff. Anybody else? Sid? Ted? Don? __________________ If it's made after 1918...it's a reproduction

09-27-2005, 09:03 PM	#3
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,022 Thanks: 1,090 Thanked 5,179 Times in 1,703 Posts	I looked at it at last year's show and measured it against my Test Eagles. I agree with Bob that the gun looks like it never had a crest. The chamber area did not look ground, but as I recall it measured .002 to .004 smaller in diameter than mine. I measured at the front of the receiver, half-way back and across the recoil lug. I don't know if that is enough to remove a crest or not. I wrote the measurements down in a little notebook, but I don't know where it is right now. If I find it, I will let you know the measurements. __________________ If it's made after 1918...it's a reproduction

09-28-2005, 03:12 PM	#4
Strider User Join Date: Jun 2002 Location: Albuquerque, New Mexico Posts: 256 Thanks: 26 Thanked 0 Times in 0 Posts	Hi Ron, I plan on being there on sometime Saturday morning. The Albuquerque Balloon Fiesta starts this weekend so the it should not be to crowded in the morning. Hopefully we will be able to see some good stuff. It will be good to see you again. I will look for you over at Bob's table. Sid. __________________ Sid. Patience is a bitter plant, but it has sweet fruit. ~German Proverb If it is made before 1930 ..........It is a prototype.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-27-2005, 08:21 PM	#2
Dwight Gruber User Join Date: Jun 2002 Location: Portland, Oregon Posts: 3,902 Thanks: 0 Thanked 1,318 Times in 431 Posts	Ron, Won't be able to be there. But if Bob Adams is, you might see if you can get a serious look at the Test Eagle-sans-Eagle that he has had for sale for a while. --Dwight