655 loading tool question

Luke99 · 04-19-2024, 08:59 AM

Hello, new to this community. So not sure where to post. I was wondering if yall who know what their talking about know if this takedown tool looks legit or not? Im not really sure what to look for. So any advice is helpful.

guns3545 · 04-19-2024, 11:40 AM

Difficult to say because of dark photos. BUT...the first, and sometimes the best test is the drop test.

Simply find a solid surface like marble, granite, ceramic, etc., found in kitchens and bathrooms or tile floors Then drop the tool from about a foot or so.

If it THUNKS. Throw it away. If it clinks like a delicate bell it's probably good.

These tools were made of very hardened steel and the hardening process gives it the clinkey, bell like sound.

Hopes this helps.

John

Luke99 · 04-19-2024, 12:01 PM

I can do that. I have also heard that the legit tools are around 2.4-2.5mm thick and most reproductions are around 3mm? The main thing im concerned about is the deep stamp? I've seen alot of legit ones with a light stamp on them.

lugerholsterrepair · 04-19-2024, 03:37 PM

WHITE backgrounds take the WORST photos with auto settings. White REFLECTS light and shuts off detail of the tool. Use a dark background for better detail.

The hole lip and the screwdriver tip are important details.

Luke99 · 04-19-2024, 06:41 PM

I agree, these are the sellers pics. I have not actually gotten the tool yet.

klaus 3338 · 04-20-2024, 02:34 AM

It's ok, you can buy it.

velodog455~ · 04-20-2024, 09:38 AM

If it's fake then I wouldn't throw it away if you plan to take it to the range occasionally. Better to use a fake as a mag loading assist tool than an original. Let it take all the finish wear and keep any originals as collectibles or display items.

Even the screwdriver blade on a fake is usually still adequate to remove the grips at the range if necessary. Some fakes are better than others in that respect.

-Bob

04-19-2024, 08:59 AM	#1
Luke99 User Join Date: Apr 2024 Posts: 6 Thanks: 1 Thanked 1 Time in 1 Post	655 loading tool question Hello, new to this community. So not sure where to post. I was wondering if yall who know what their talking about know if this takedown tool looks legit or not? Im not really sure what to look for. So any advice is helpful. Attached Thumbnails

04-19-2024, 03:37 PM	#4
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	WHITE backgrounds take the WORST photos with auto settings. White REFLECTS light and shuts off detail of the tool. Use a dark background for better detail. The hole lip and the screwdriver tip are important details. __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-19-2024, 11:40 AM	#2
guns3545 Lifer Lifetime Forum Patron Join Date: Aug 2006 Location: Florida Posts: 437 Thanks: 655 Thanked 492 Times in 218 Posts	Difficult to say because of dark photos. BUT...the first, and sometimes the best test is the drop test. Simply find a solid surface like marble, granite, ceramic, etc., found in kitchens and bathrooms or tile floors Then drop the tool from about a foot or so. If it THUNKS. Throw it away. If it clinks like a delicate bell it's probably good. These tools were made of very hardened steel and the hardening process gives it the clinkey, bell like sound. Hopes this helps. John

04-19-2024, 12:01 PM	#3
Luke99 User Join Date: Apr 2024 Posts: 6 Thanks: 1 Thanked 1 Time in 1 Post	I can do that. I have also heard that the legit tools are around 2.4-2.5mm thick and most reproductions are around 3mm? The main thing im concerned about is the deep stamp? I've seen alot of legit ones with a light stamp on them.

04-19-2024, 06:41 PM	#5
Luke99 User Join Date: Apr 2024 Posts: 6 Thanks: 1 Thanked 1 Time in 1 Post	I agree, these are the sellers pics. I have not actually gotten the tool yet.

04-20-2024, 02:34 AM	#6
klaus 3338 User Join Date: Jun 2009 Location: Germany Posts: 517 Thanks: 0 Thanked 411 Times in 160 Posts	It's ok, you can buy it.

04-20-2024, 09:38 AM	#7
velodog455~ User Join Date: Aug 2023 Posts: 76 Thanks: 18 Thanked 58 Times in 35 Posts	If it's fake then I wouldn't throw it away if you plan to take it to the range occasionally. Better to use a fake as a mag loading assist tool than an original. Let it take all the finish wear and keep any originals as collectibles or display items. Even the screwdriver blade on a fake is usually still adequate to remove the grips at the range if necessary. Some fakes are better than others in that respect. -Bob