Correct bluing for 1902 ae

wayne8661 · 03-15-2009, 09:12 PM

I am doing some more research into having my AE fat barrel restored. I have found a gentleman who does nice work I havent committed to anything but What is the proper bluing method for this year pistol? Also have any of you had restorations done were you pleased with the results? I have seen this guys work and he does a great job I am just soooo nervous about giving this weapon to ANYBODY

Edward Tinker · 03-15-2009, 09:27 PM

I can't remember if your fat barrel is messed up or not....

Just be aware that once "restored" / refinished or touched, it can not be "undone"...

Unless a basket case or you hope to make money later (hard to do) on it; then rebluing it is strictly for your own pleasure.

Ed

wayne8661 · 03-15-2009, 09:29 PM

My fat barrel was parkerized at some point.

Edward Tinker · 03-15-2009, 09:30 PM

yes I saw that, once I did a search of your posts

I would think that if you can get it restored it would be nice to do so.

Whomever you get to "restore" it, they need to know lugers, and they'll know the proper blue to put on it. If you just get a guy who does good work, the color will be off or too black or too shiney.

Ed

wayne8661 · 03-15-2009, 09:31 PM

Yes I do agree The pistol is solid and there is no pitting so I think it will clean up nicely I am just scared to actually go through with a restoration

Ron Wood · 03-15-2009, 09:34 PM

The finish on a 1902 is rust blue, a bit more demanding and time consuming that the hot salt blue of WWII Lugers. The most critical part of restoration is preparaton of the metal. Care must be taken not to round over sharp contours or remove markings. For a quality job, this requires mostly hand work. If the refiniser even mentions a buffing wheel - run away. You have already had Ken Karsted recommended as a possibility to consider. He knows what he is doing.

wayne8661 · 03-15-2009, 09:37 PM

Ron I thought Ken Was not accepting work

wayne8661 · 03-15-2009, 09:39 PM

Does anyone have contact info for Ken ?

wayne8661 · 03-15-2009, 10:04 PM

I actually missed Kens number on my original post I will definately contact him and see what he says

Tomathvl · 03-16-2009, 09:22 AM

Ken Karsted
847-234-0441

chuck watts · 03-16-2009, 05:49 PM

Wayne,

Try galemorgan.com

Chuck

wayne8661 · 03-16-2009, 08:24 PM

Well I have contacted Ken Karsted and spoke with him. A ver nice gentleman we talked for a bit and I got a warm fuzzy from him. I also did drop an email to Gale Morgan and sent photos havent heard back from him yet.

Navy · 03-17-2009, 10:59 AM

Have been told that Morgan is not taking any new work.

Tom A

chuck watts · 03-17-2009, 05:57 PM

Hi Tom,

Talked with Gale about 2 months ago, he told me he was accepting new work.

Chuck

wayne8661 · 03-18-2009, 08:56 PM

Have any of you had Ken do work on anything/? If so Could you post a pic for me? I am anxious to see what my pistol could possibly look like.

Ron Wood · 03-18-2009, 10:30 PM

Wayne,
In your original thread "1902 Fat Barrel Discovered", Tomathyl posted a link to a "shooter' he owns that was finished by Ken.

Tomathvl · 03-18-2009, 11:01 PM

http://forum.lugerforum.com/showthre...light=tomathvl

03-15-2009, 09:12 PM	#1
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Correct bluing for 1902 ae I am doing some more research into having my AE fat barrel restored. I have found a gentleman who does nice work I havent committed to anything but What is the proper bluing method for this year pistol? Also have any of you had restorations done were you pleased with the results? I have seen this guys work and he does a great job I am just soooo nervous about giving this weapon to ANYBODY

03-15-2009, 09:27 PM	#2
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,935 Thanks: 2,034 Thanked 4,533 Times in 2,093 Posts	I can't remember if your fat barrel is messed up or not.... Just be aware that once "restored" / refinished or touched, it can not be "undone"... Unless a basket case or you hope to make money later (hard to do) on it; then rebluing it is strictly for your own pleasure. Ed __________________ Edward Tinker ************ Co-Author of Police Lugers - Co-Author of Simson Lugers Author of Veteran Bring Backs Vol I, Vol II, Vol III and Vol IV

03-15-2009, 09:34 PM	#6
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,022 Thanks: 1,090 Thanked 5,179 Times in 1,703 Posts	The finish on a 1902 is rust blue, a bit more demanding and time consuming that the hot salt blue of WWII Lugers. The most critical part of restoration is preparaton of the metal. Care must be taken not to round over sharp contours or remove markings. For a quality job, this requires mostly hand work. If the refiniser even mentions a buffing wheel - run away. You have already had Ken Karsted recommended as a possibility to consider. He knows what he is doing. __________________ If it's made after 1918...it's a reproduction

03-16-2009, 05:49 PM	#11
chuck watts User Join Date: May 2006 Location: USA Posts: 20 Thanks: 0 Thanked 0 Times in 0 Posts	Wayne, Try galemorgan.com Chuck __________________ chuck watts

03-17-2009, 05:57 PM	#14
chuck watts User Join Date: May 2006 Location: USA Posts: 20 Thanks: 0 Thanked 0 Times in 0 Posts	Hi Tom, Talked with Gale about 2 months ago, he told me he was accepting new work. Chuck __________________ chuck watts

03-15-2009, 09:29 PM	#3
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	My fat barrel was parkerized at some point.

03-15-2009, 09:30 PM	#4
Edward Tinker Super Moderator Eternal Lifer LugerForum Patron Join Date: Jun 2002 Location: North of Spokane, WA Posts: 15,935 Thanks: 2,034 Thanked 4,533 Times in 2,093 Posts	yes I saw that, once I did a search of your posts I would think that if you can get it restored it would be nice to do so. Whomever you get to "restore" it, they need to know lugers, and they'll know the proper blue to put on it. If you just get a guy who does good work, the color will be off or too black or too shiney. Ed

03-15-2009, 09:31 PM	#5
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Yes I do agree The pistol is solid and there is no pitting so I think it will clean up nicely I am just scared to actually go through with a restoration

03-15-2009, 09:37 PM	#7
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Ron I thought Ken Was not accepting work

03-15-2009, 09:39 PM	#8
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Does anyone have contact info for Ken ?

03-15-2009, 10:04 PM	#9
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	I actually missed Kens number on my original post I will definately contact him and see what he says

03-16-2009, 09:22 AM	#10
Tomathvl User Join Date: May 2004 Location: Milan, IN Posts: 363 Thanks: 3 Thanked 48 Times in 19 Posts	Ken Karsted 847-234-0441

03-16-2009, 08:24 PM	#12
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Well I have contacted Ken Karsted and spoke with him. A ver nice gentleman we talked for a bit and I got a warm fuzzy from him. I also did drop an email to Gale Morgan and sent photos havent heard back from him yet.

03-17-2009, 10:59 AM	#13
Navy RIP Join Date: Jun 2002 Location: Dc 'burbs in Virginia Posts: 2,482 Thanks: 0 Thanked 16 Times in 10 Posts	Have been told that Morgan is not taking any new work. Tom A

03-18-2009, 08:56 PM	#15
wayne8661 User Join Date: Nov 2008 Location: Kennett Square Pennsylvania Posts: 591 Thanks: 15 Thanked 334 Times in 104 Posts	Have any of you had Ken do work on anything/? If so Could you post a pic for me? I am anxious to see what my pistol could possibly look like.

03-18-2009, 10:30 PM	#16
Ron Wood Moderator 2010 LugerForum Patron Join Date: Jun 2002 Location: Santa Teresa New Mexico just outside of the West Texas town of El Paso Posts: 7,022 Thanks: 1,090 Thanked 5,179 Times in 1,703 Posts	Wayne, In your original thread "1902 Fat Barrel Discovered", Tomathyl posted a link to a "shooter' he owns that was finished by Ken. __________________ If it's made after 1918...it's a reproduction

03-18-2009, 11:01 PM	#17
Tomathvl User Join Date: May 2004 Location: Milan, IN Posts: 363 Thanks: 3 Thanked 48 Times in 19 Posts	http://forum.lugerforum.com/showthre...light=tomathvl