Shootin'

FNorm · 05-11-2009, 11:50 PM

Made it to the range today with some new toys. The mostly 41 byf ,this is one with at least 5 different serial numbers in it, a war bring back, shot really well. With any magazine, and three different length cartridges. Everything from Win. white label at 1.160 OAL, to my much shorter hand loads, 1.073 And accurately!

The 7.65 commercial has a problem. It loads and ejects just fine, but the firing pin isn't getting cocked upon return to battery. I can drop the magazine, pull back the toggle a half inch, let it go and it all fires again. So???? Any suggestions? This is with who knows how old ammo though. Still if it loads and ejects???? I've really got in there tonight and scrubbed everything down. Some dirt in the breech block. Try again next week. Then I might be talking with LugerDoc....

FN

policeluger · 05-12-2009, 12:35 AM

Your sear surface may have a one time been trimmed down so short as to not lock on firing....check and see the depth of the engagement....

Sieger · 05-13-2009, 09:27 PM

Quote:

Originally Posted by FNorm

Made it to the range today with some new toys.

The mostly 41 byf ,this is one with at least 5 different serial numbers in it, a war bring back, shot really well.

With any magazine, and three different length cartridges. Everything from Win. white label at 1.160 OAL, to my much shorter hand loads, 1.073 And accurately!

FN

FNorm:

I have no doubt you fired them accurately, but could you fire a full magazine of 8 reliably?

For round nose you should strive for an OAL of 1.169 to 1.173,
for truncated cone, 1.15.

I also own a BYF 41, and these are really nice pistols.

Sieger

FNorm · 05-13-2009, 09:40 PM

Didn't have the tool so could only get 5-6 rounds in. I'm old. Hands hurt sometimes.

Lead me by said hand as to how to check the engagement depth?

FN

John Sabato · 05-14-2009, 10:11 AM

Measuring is easy...

Degrease and de-oil the surfaces with alcohol.

Then use a good black magic marker to color the engagement surface of the sear, and / or firing pin. Assemble and dry fire a few times. Then disassemble and measure the depth of engagement by checking to see how much marker has been scratched on each piece by the two surfaces rubbing together.

FNorm · 05-17-2009, 11:09 PM

Found the fix, a sticky in the "repairs restorations section"

Apparently the the slide is de-cocking itself cuz of lack a clearance between the trigger bar, and the push pin on the front of the sear.

FN

05-11-2009, 11:50 PM	#1
FNorm Patron LugerForum Patron Join Date: Mar 2009 Location: Colorado Posts: 978 Thanks: 68 Thanked 127 Times in 108 Posts	Shootin' Made it to the range today with some new toys. The mostly 41 byf ,this is one with at least 5 different serial numbers in it, a war bring back, shot really well. With any magazine, and three different length cartridges. Everything from Win. white label at 1.160 OAL, to my much shorter hand loads, 1.073 And accurately! The 7.65 commercial has a problem. It loads and ejects just fine, but the firing pin isn't getting cocked upon return to battery. I can drop the magazine, pull back the toggle a half inch, let it go and it all fires again. So???? Any suggestions? This is with who knows how old ammo though. Still if it loads and ejects???? I've really got in there tonight and scrubbed everything down. Some dirt in the breech block. Try again next week. Then I might be talking with LugerDoc.... FN

05-14-2009, 10:11 AM	#5
John Sabato Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: The Capital of the Free World Posts: 10,154 Thanks: 3,003 Thanked 2,306 Times in 1,097 Posts	Measuring is easy... Degrease and de-oil the surfaces with alcohol. Then use a good black magic marker to color the engagement surface of the sear, and / or firing pin. Assemble and dry fire a few times. Then disassemble and measure the depth of engagement by checking to see how much marker has been scratched on each piece by the two surfaces rubbing together. __________________ regards, -John S "...We hold these truths to be self-evident that ALL men are created EQUAL *and are endowed by their Creator* with certain UNALIENABLE* rights, and among these are life, LIBERTY, and the pursuit of happiness..."*

05-12-2009, 12:35 AM	#2
policeluger RIP Join Date: Jun 2002 Location: Ca. Posts: 2,141 Thanks: 8 Thanked 89 Times in 54 Posts	Your sear surface may have a one time been trimmed down so short as to not lock on firing....check and see the depth of the engagement....

05-13-2009, 09:40 PM	#4
FNorm Patron LugerForum Patron Join Date: Mar 2009 Location: Colorado Posts: 978 Thanks: 68 Thanked 127 Times in 108 Posts	Didn't have the tool so could only get 5-6 rounds in. I'm old. Hands hurt sometimes. Lead me by said hand as to how to check the engagement depth? FN

05-17-2009, 11:09 PM	#6
FNorm Patron LugerForum Patron Join Date: Mar 2009 Location: Colorado Posts: 978 Thanks: 68 Thanked 127 Times in 108 Posts	Found the fix, a sticky in the "repairs restorations section" Apparently the the slide is de-cocking itself cuz of lack a clearance between the trigger bar, and the push pin on the front of the sear. FN