AEG Drum Loader

regul · 05-31-2016, 05:51 PM

I would like the opinion of the forum on this AEG loader. I know the screw is installed from the opposite side from what is considered normal.
Thanks
Ed

George Anderson · 05-31-2016, 07:23 PM

Looks just like mine except for the screw.

Norme · 05-31-2016, 07:27 PM

Hi Ed,
AEG loaders are very rare and desirable and despite the reversed screw yours looks authentic to me. I don't own one of these, but I'm wondering whether your handle is simply installed upside down. Let us know if you have tried reversing it.
Regards, Norm

lugerholsterrepair · 05-31-2016, 09:00 PM

I'm wondering whether your handle is simply installed upside down. That's a good point but if the handle were turned..the plunger would be backwards?

George, Is the AEG logo on the opposite side of the handle?

George Anderson · 05-31-2016, 09:11 PM

Quote:

Originally Posted by lugerholsterrepair

George, Is the AEG logo on the opposite side of the handle?

It's on the same side as his.

regul · 05-31-2016, 09:43 PM

George, Norme & Jerry
Thank all of you for your replies. I tried flipping the handle upside down and that puts the cartridge pusher backwards. I think when it was made either the hole for the screw was started on the wrong side or when the parts were riveted together something was reversed. I have attached another photo that shows it better than I can explain.
Thanks
Ed

lugerholsterrepair · 05-31-2016, 09:57 PM

Ed, Yes that would be correct.

Ed, Question..the screw..on Bing loaders the screw inserts into a tubeular sleeve. The sleeve seems to be missing or you don't show it? The handle would be sloppy at the screw end without the screw.

That's IF the AEG loaders had the same sleeve?

The AEG logo is correct on the left side but it's upside down.

regul · 06-01-2016, 06:45 AM

Jerry
There is no sleeve on this one, which I think is correct for the AEG Loaders. I have three Bing loaders, one long body and two short body which all have the sleeve in place.
I added a couple of photos to the previous post.
Thanks
Ed

G.T. · 06-01-2016, 09:36 AM

Hi to all, as the handle is symmetrical it is an easy mistake to make at the factory to rivet the compression attachment on upside down, and rather then toss it, its an Awwww crap! I'll just put the screw in from the opposite side.. I'll bet there's more just like it, although there should be a majority, or correct assembly procedure that was supposed to be followed.... No other reason, unless a careless repair at some time?..... til..lat'r...GT...

Kitkat041836 · 06-01-2016, 12:19 PM

Hi guys, this handle was put on wrong at the factory.The guy just
sent it on it's way.He drilled and taped it from the wrong side.There is no tube in a A.E.G. like the Bing loader
Thanks,The fatkat,George

lugerholsterrepair · 06-01-2016, 12:30 PM

Thanks! You learn something everyday if your not careful.

regul · 06-04-2016, 12:06 AM

Sorry for the late thank you's for everyones input. Work got in the way of pleasure the last few days.
Again thanks
Ed

05-31-2016, 05:51 PM	#1
regul Patron LugerForum Patron Join Date: Sep 2002 Location: VA Posts: 96 Thanks: 19 Thanked 57 Times in 20 Posts	AEG Drum Loader I would like the opinion of the forum on this AEG loader. I know the screw is installed from the opposite side from what is considered normal. Thanks Ed Attached Thumbnails Attached Images

05-31-2016, 09:00 PM	#4
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	I'm wondering whether your handle is simply installed upside down. That's a good point but if the handle were turned..the plunger would be backwards? George, Is the AEG logo on the opposite side of the handle? __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

05-31-2016, 09:43 PM	#6
regul Patron LugerForum Patron Join Date: Sep 2002 Location: VA Posts: 96 Thanks: 19 Thanked 57 Times in 20 Posts	AEG (Berlin) Loading Tool George, Norme & Jerry Thank all of you for your replies. I tried flipping the handle upside down and that puts the cartridge pusher backwards. I think when it was made either the hole for the screw was started on the wrong side or when the parts were riveted together something was reversed. I have attached another photo that shows it better than I can explain. Thanks Ed Attached Thumbnails

05-31-2016, 09:57 PM	#7
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	Ed, Yes that would be correct. Ed, Question..the screw..on Bing loaders the screw inserts into a tubeular sleeve. The sleeve seems to be missing or you don't show it? The handle would be sloppy at the screw end without the screw. That's IF the AEG loaders had the same sleeve? The AEG logo is correct on the left side but it's upside down. __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

06-01-2016, 09:36 AM	#9
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,507 Thanks: 1,318 Thanked 3,653 Times in 1,004 Posts	Awww crap! Hi to all, as the handle is symmetrical it is an easy mistake to make at the factory to rivet the compression attachment on upside down, and rather then toss it, its an Awwww crap! I'll just put the screw in from the opposite side.. I'll bet there's more just like it, although there should be a majority, or correct assembly procedure that was supposed to be followed.... No other reason, unless a careless repair at some time?..... til..lat'r...GT...

05-31-2016, 07:23 PM	#2
George Anderson Lifer Lifetime Forum Patron Join Date: Jul 2002 Location: VA Posts: 3,592 Thanks: 1,773 Thanked 2,529 Times in 787 Posts	Looks just like mine except for the screw.

05-31-2016, 07:27 PM	#3
Norme Always A Lifetime Forum Patron Join Date: Jul 2009 Location: Colorado Posts: 2,417 Thanks: 226 Thanked 2,603 Times in 933 Posts	Hi Ed, AEG loaders are very rare and desirable and despite the reversed screw yours looks authentic to me. I don't own one of these, but I'm wondering whether your handle is simply installed upside down. Let us know if you have tried reversing it. Regards, Norm

06-01-2016, 06:45 AM	#8
regul Patron LugerForum Patron Join Date: Sep 2002 Location: VA Posts: 96 Thanks: 19 Thanked 57 Times in 20 Posts	Jerry There is no sleeve on this one, which I think is correct for the AEG Loaders. I have three Bing loaders, one long body and two short body which all have the sleeve in place. I added a couple of photos to the previous post. Thanks Ed

06-01-2016, 12:19 PM	#10
Kitkat041836 RIP Join Date: Feb 2009 Posts: 195 Thanks: 0 Thanked 21 Times in 18 Posts	Handle put on wrong at factory. Hi guys, this handle was put on wrong at the factory.The guy just sent it on it's way.He drilled and taped it from the wrong side.There is no tube in a A.E.G. like the Bing loader Thanks,The fatkat,George

06-01-2016, 12:30 PM	#11
lugerholsterrepair Moderator Lifetime Forum Patron Join Date: Jun 2002 Location: Arizona/Colorado Posts: 7,772 Thanks: 4,940 Thanked 3,124 Times in 1,434 Posts	Thanks! You learn something everyday if your not careful. __________________ Jerry Burney 11491 S. Guadalupe Drive Yuma AZ 85367-6182 l[email protected] 928 342-7583 (CO & AZ) Year Round 719 207-3331 (cell) "For those who Fight For It, Life has a flavor the protected will never know."

06-04-2016, 12:06 AM	#12
regul Patron LugerForum Patron Join Date: Sep 2002 Location: VA Posts: 96 Thanks: 19 Thanked 57 Times in 20 Posts	Sorry for the late thank you's for everyones input. Work got in the way of pleasure the last few days. Again thanks Ed